1. Genie Scissor Lift 1930 For Sale

When you select the 'Remember me' option, your login information will be stored on your computer in the form of a cookie. When you visit Forkliftaction.com again, the stored login information will be retrieved automatically and you will not have to submit your login parameters (email address and password) each time you want to visit our members-only pages.

A cookie is a small piece of data that is sent to your browser from a web server and stored on your computer's hard drive. A cookie can't read data off your hard disk or read cookie files created by other sites. Cookies do not damage your system. Forum: Discussion: 2015 GENIE GS1930 ERROR CODE C021 Number of messages: 10 START MESSAGE: Hawaii, United States I have a 2015 GENIE GS1930 ERROR CODE ' C021: PCON NOT DETECTED'. Repair Manual Possible Cause: 1) PCON Disconnected. 2) CAN Communication Failure. 3) GCOPN or PCON ECM.

When I go up with the Lift about 10-ft., Lift Stops and give Error Code C021. I press the 'Stop' button to reset and try to go up. Lift stop at about 2-ft and give the Error Code C021. I reset it and does the same thing at another 2-ft. I switch to 'Ground Control' and does the same thing. I switched 'Platform Control' with a working '2-Button Gen 6 Platform Control' and same thing. I switched the 'Ground Control' and gave a different code from the start, 'C051: SYSTEM FAULT TILT: NoCal'.

I want to call Genie Support, but there's NONE. I tried to find any Genie Scissorlift Forum, but there's none. Only Forklift Action. Can someone help me? Posted 12 Mar 2018 06:24 PM REPLIES: Sort replies by Reggio Emilia, Italy Try to temporarily eliminate the pressure sensor mounted near the oil filter.

The problem should be solved good job Posted 13 Mar 2018 06:38 AM Hawaii, United States Technically, I can't see how a pressure sensor is connected to the ECM or any of the Controllers to give the Code C021. Posted 13 Mar 2018 07:05 AM Reggio Emilia, Italy I had a similar problem with a canbus failure alarm. Fixed changing the pressure sensor. Posted 13 Mar 2018 07:54 AM Hawaii, United States On the Hydraulic Manifold.

There's no Pressure Sensor, only Pressure Relief Valve & Solenoids. Can you give me a Genie Part Number so I can locate the part you mention. Posted 13 Mar 2018 11:10 AM Nebraska, United States PCON stands for platform control. Code 21 is lost communication from platform controller to chassis controller. This is a lost CANbus signal. Posted 13 Mar 2018 11:48 PM Nebraska, United States Manuals are available. Search for genie manlift, you will find the web site.

Posted 13 Mar 2018 11:49 PM Hawaii, United States I have review the Genie GS-1930 Repair Manual. Review the Hydraulic and Electrical Schematics. I can see the one of these might be the problem: 1) S14-Platform Height Sensor. 2) PT15-Platform Overload Sensor (Pressure Transducer).

Genie Scissor Lift 1930 For Sale

Only problem, inspected the lift, Non of the Sensor Exist (There's None). I looked at my older GS-1930, there's no such thing. Posted 14 Mar 2018 04:10 PM Wisconsin, United States I think you have a broken wire in the harness from the platform control to the ground controls. Ohm them all out.

Posted 16 Mar 2018 02:33 PM Hawaii, United States I have by-passed the wiring harness which goes to the platform control and connected direct to the Ground Control. And still does the same. Tech who worked on Genie know what I'm talking about. I have reviewed the schematics. If there were the Over-load Pressure Sensor or the Lift Height Sensor.

That would make sense of the problem. But, there's NONE to be found on the scissorlift. Next, I would figure the Tilt Sensor needs Calibrating. What do you all think?? Posted 16 Mar 2018 03:13 PM. Click for description.

A place for members to share ideas or ask questions. Every Forum is focused on a subject. Choose an area that is of interest. A series of messages in chronological order; a conversation about a Forum subject.

Start a new discussion with a question, a comment or an idea, and let fellow members respond. Each text contribution within a discussion, as posted by a member. All messages contain details about the author and the time of posting.

Any member can contribute to any discussion in every forum. This is your unique Forum identity. You may choose your first name or any other nickname. It must be a unique name: 'first in, first served'.

A short message created in your Forum profile, which you may opt to attach to any of your messages. This could be a slogan, anecdote or greeting.

Genie wiring diagrams, hydraulic diagrams and pneumatic diagrams for Genie Aluminum products, Genie S-Booms, Genie Scissors, Genie TMZs, Genie Verticals, and Genie Z-Booms. Telescopic Stick Booms S40/45 Ford 2WD & 4WD S40/45 Deutz/Perkins 2WD & 4WD S40/45 Hydraulics S60/65 Ford 2WD & 4WD S60/65 Deutz/Perkins 2WD & 4WD S60/65 Hydraulics S80/85 Ford 2WD & 4WD S80/85 Deutz/Perkins 2WD & 4WD S80/85 Hydraulics Scissors & Vertical Lifts GS 1530, 1930, 2032, 2046, 2646, 3246 GS 2668, 3268 DC GS 2668, 3268 RT V4M V1832, V1854, V2470 DC V2470 RT & DRT Articulating Z-Booms Z20/8 Z25/8 Z30/20 Standard & HD G.E. Motor Controller Z30/20 Curtis Motor Controller Z30/20N Z34/22N Z34/22DC & Bi-Energy Z34/22IC GP/LP Z34/22IC Diesel Z34/22 Hydraulics Z45/22 DC Z45/22 GP (HP,MP) Z45/22 Diesel (HP,MP) Z45/22 Hydraulics Z45/22 Tri-Fuel Z45/25 DC & Bi-Energy Z45/25 IC Z60/34 Ford Z60/34 Deutz Z60/34 Hydraulics Aluminum & TMZ Products PLC/PLI/EUP AWP 1 AWP 2 AWP Super Series IWP IWP Super Series CWP/SP Super Series DPL DPL Super Series Super Hoist / PSL-Load Handler / PSL Advantage TMZ Screenshots for Genie Schematic & Diagram Manual.